АРТИКУЛ;ОПИСАНИЕ ТОВАРА

BUS ; Additional price for execution of D1000 in a corps with the sockets of tire of feed of POWER BUS CABF004 ; Кабель 6 pin cable (RJ-12 jack) CABF005 ; 15 см flat cable for connection of the modules D2010M - D2011M CABF006 ; Cable Flat Cable for connections D2010M-D2011M, length 30 cm CABF007 ; 50 см flat cable for connection of the modules D2010M - D2011M CABF008 ; Cable Cable to interconnect D2050M with D2010Mor D2030M units (price per meter), CABF010 ; Cable Sub D 9 Poles Female-Female Nul-Modem, 1800 mm lenght for RS-232 connection CABF012 ; Cable for tenzometrical (price for a 1 meter) CABF022 ; 15 см flat cable for connection of the modules D2050M - D2052M - D2053M CABF023 ; 30 cсм flat cable for connection of the modules D2050M - D2052M - D2053M CABF024 ; 50 см flat cable for connection of the modules D2050M - D2052M - D2053M CABF025 ; Cable loop, 30 cm flat cable to interconnect two PBCO-16-037 Boards CABF026 ; Кабель 75 cm Flat Cable for connecting Hart Multiplexer Supporting Boards to D5000 Series Boards CABF027 ; Кабель 100 cm Flat Cable for connecting Hart Multiplexer Supporting Boards to D5000 Series Boards CABF030 ; Cable assembling Cable Assembly for PBCO, Connect Module Safe Area terminals to Board D1000D ; Empty module for application with the made to order pays D1000R ; Framework one 19-inch, for setting 16 modules of series of D1000, height 3U D1002S ; Module an emergency Redundant Connection and Common Alarm Module (SPST) for D1000 Series, Max. 4 Amps D1010D ; Licensed key on a compact disk disk, we will confront with intellectual sensors, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current, SIL3 (1 year)/SIL2 (5 yr) D1010D 0-10V OUT ; Licensed key on a compact disk disk, we will confront with intellectual sensors, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, exit сконфигурирован на диапазон 0-10В D1010D/B ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2 D1010D-002 ; Transformer signalов, 2 Input Ch. 0 - 5 Vdc / 2 Output 4-20 mA, Fixed Range D1010D-026 ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 4-20 мА, exitы 0-10В D1010D-026/B ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 4-20 мА, exitы 0-10В D1010D-029 ; Transformer signalов, 2 Input Ch. -20 + 20 mA / 2 Output 0-20 mA, Fixed Range D1010D-030 ; Transformer signalов, 2 Input Ch. 0 - 10 Vdc / 2 Output 4-20 mA, Fixed Range D1010D-035 ; Transformer signalов, 2 Input Ch. 0 - 15 Vdc / 2 Output 4-20 mA, Fixed Range D1010D-036 ; Transformer signalов, 2 Input Ch. 0 - 20 mA / 2 Output 0-20 mA, Fixed Range D1010D-041 ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-1.4 mA, exitы 0-20 mA/0-5V D1010D-041/B ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-1.4 mA, exitы 0-20 mA/0-5V D1010D-043 ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-450 мВ, exitы 0-1,4 мА D1010D-043/B ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-450 мВ, exitы 0-1,4 мА D1010D-046 ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 3 (1 year)/SIL 2 (5 years) D1010D-046/B ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 3 (1 year)/SIL 2 (5 years) D1010D-047 ; Licensed key on a compact disk disk, Analog Input, 2 Channel, 4-20 mA Input, 0-5 V or 0-10 V Output D1010D-047/B ; Licensed key on a compact disk disk, Analog Input, 2 Channel, 4-20 mA Input, 0-5 V or 0-10 V Output D1010D-048 ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entranceы 0/4-20 мА, exitы 0/0,2-1 mA D1010D-048/B ; Licensed key on a compact disk disk, 2 channelа, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entranceы 0/4-20 мА, exitы 0/0,2-1 mA D1010D-061 ; Transformer signalов, 2 Input Ch. 0 - 40 Vdc / 2 Output 4-20 mA, Fixed Range D1010S ; Licensed key on a compact disk disk, we will confront with intellectual sensors, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current, SIL 3 (1 yr)/SIL 2 ( 5 yr) D1010S/B ; Licensed key on a compact disk disk, we will confront with intellectual sensors, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2 D1010S-010 ; Transformer signalов, 1 Input Ch. -30 + 30 Vdc / 1 Output 4-20 mA, Fixed Range D1010S-015 ; Transformer signalов, 1 Input Ch. 0 - 50 Vdc / 1 Output 4-20 mA, Fixed Range D1010S-016 ; Transformer signalов, 1 Input Ch. 0 - 120 mVdc / 1 Output 4-20 mA, Fixed Range D1010S-017 ; Transformer signalов, 1 Input Ch. -10 + 10 Vdc / 1 Output 4-20 mA, Fixed Range D1010S-023 ; Transformer signalов, 1 Input Ch. -5 + 5 Vdc / 1 Output 4-20 mA, Fixed Range D1010S-026 ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 4-20 мА, exit 0-10В D1010S-026/B ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 4-20 мА, exit 0-10В D1010S-038 ; Transformer signalов, 1 Input Ch. -50 + 50 Vdc / 1 Output 4-20 mA, Fixed Range D1010S-041 ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-20 мА,, exit 0-5В D1010S-041/B ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-20 мА,, exit 0-5В D1010S-043 ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-450 мВ, exit 0-1,4 мА D1010S-043/B ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0-450 мВ, exit 0-1,4 мА D1010S-046 ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 3 (1 year)/SIL 2 (5 years) D1010S-046/B ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 3 (1 year)/SIL 2 (5 years) D1010S-047 ; Licensed key on a compact disk disk, Analog Input, 1 Channel, 4-20 mA Input, 0-5 V or 0-10 V Output D1010S-047/B ; Licensed key on a compact disk disk, Analog Input, 1 Channel, 4-20 mA Input, 0-5 V or 0-10 V Output D1010S-048 ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0/4-20 мА, exit 0/0,2-1 мА D1010S-048/B ; Licensed key on a compact disk disk, 1 channel, Smart-Hart, active-passive entrance, an exit is a source-receiver of current - SIL 2, entrance 0/4-20 мА, exit 0/0,2-1 мА D1010S-054 ; Licensed key on a compact disk disk, 1 channel, entranceы -5 - +55 mV, exit 4-20 mA, SIL 2 (5yr) D1010S-054/B ; Licensed key on a compact disk disk, 1 channel, entranceы -5 - +55 mV, exit 4-20 mA, SIL 2 (5yr) D1010S-055 ; Transformer signalов, 1 Input Ch. 0 - 70 Vdc / 1 Output 4-20 mA, Fixed Range D1010S-056 ; Licensed key on a compact disk disk, 1 channel,entranceы -5 - +35 mV, exit 4-20 mA, SIL 2 (5 years) D1010S-056/B ; Licensed key on a compact disk disk, 1 channel,entranceы -5 - +35 mV, exit 4-20 mA, SIL 2 (5 years) D1010S-057 ; Licensed key on a compact disk disk, 1 channel,entranceы -5 - +10 mV, exit 4-20 mA, SIL 2 (5 years) D1010S-057/B ; Licensed key on a compact disk disk, 1 channel,entranceы -5 - +10 mV, exit 4-20 mA, SIL 2 (5 years) D1012Q ; Licensed key on a compact disk disk fourchannel D1014D ; Licensed key on a compact disk disk c by an enhanceable faulttolerance, 2 channelа, Hart, passive entrance 4-20мА, an exit is a source of current 4-20мА, SIL 3 (1 yr)/SIL 2 (5yr) D1014D/B ; Licensed key on a compact disk disk, 2 channelа, Hart, passive entrance 4-20мА, an exit is a source of current 4-20мА, SIL 2, SIL 3 D1014D-083 ; Модуль искрозащиты с гальваническим разделением 2 Independent Ch, Hart, 4-20 mA Pass. IN, 2-10 Volt Output, SIL 3 (1yr)/SIL 2 (10yr) D1014S ; Licensed key on a compact disk disk with an enhanceable faulttolerance(SIL2) for the systems of safety, 1 channel, Hart, passive entrance 4-20мА, an exit is a source of current 4-20мА, SIL 3 (1 yr)/SIL 2 (10 yr) D1014S/B ; Licensed key on a compact disk disk with an enhanceable faulttolerance(SIL2) for the systems of safety, 1 channel, Hart, passive entrance 4-20мА, an exit is a source of current 4-20мА, SIL 3 (1 yr)/SIL 2 (10 yr) D1014S-060 ; Licensed key on a compact disk disk, Analogue input, 1 Channel, Hart, 4-20 mA Passive In, 4-20 mA Sink-Source Out 1 K?, SIL 3 (1yr)/SIL 2 (10yr) D1014S-060/B ; Licensed key on a compact disk disk, Analogue input, 1 Channel, Hart, 4-20 mA Passive In, 4-20 mA Sink-Source Out 1 K?, SIL 3 (1yr)/SIL 2 (10yr) D1014S-083 ; Модуль искрозащиты с гальваническим разделением 1 Ch, Hart, 4-20 mA Pass. IN, 2-10 Volt Output, SIL 3 (1yr)/SIL 2 (10yr) D1020D ; Insulating driver with a feed from a tire, 2 channelа, consonant with the intellectual field devices, SIL 2 (1 yr) D1020D/B ; Insulating driver with a feed from a tire, 2 channelа, consonant with the intellectual field devices, SIL 2 D1020D-027 ; Insulating driver with a feed from a tire, consonant with the intellectual field devices, 2 channelа, entrance: 2 - 10 В, exit: 4-20 mA D1020D-027/B ; Insulating driver with a feed from a tire, consonant with the intellectual field devices, 2 channelа, entrance: 2 - 10 В, exit: 4-20 mA D1020D-050 ; Isolated driver 2 Channel, Smart-HART, Isolating Driver for I/P, Input 0 - 10 V, Output 4-20 mA D1020D-067 ; Isolated driver 2 Channel, Smart-HART, Isolating Driver for I/P, Input 1 - 5 V, Output 4-20 mA D1020S ; Insulating driver with a feed from a tire, 1 channel, consonant with the intellectual field devices, SIL 2 (1 yr) D1020S/B ; Insulating driver with a feed from a tire, 1 channel, consonant with the intellectual field devices, SIL 2 D1020S-027 ; Insulating driver with a feed from a tire, consonant with the intellectual field devices, 1 channel, entrance: 2 - 10 В, exit: 4-20 mA D1020S-027/B ; Insulating driver with a feed from a tire, consonant with the intellectual field devices, 2 channelа, entrance: 2 - 10 В, exit: 4-20 mA D1020S-050 ; Isolated driver 1 Channel, Smart-HART, Isolating Driver for I/P, Input 0 - 10 V, Output 4-20 mA D1020S-067 ; Isolated driver 1 Channel, Smart-HART, Isolating Driver for I/P, Input 1 - 5 V, Output 4-20 mA D1020S-074 ; Isolated driver 1 Channel, Smart-HART, Isolating Driver for I/P, Input 0 - 4 V, Output 4-20 mA D1021S ; Insulating driver with a feed from a tire, consonant with the intellectual field devices, 1 channel, faultlocation of chain, SIL 2 (1 yr) D1021S/B ; Insulating driver with a feed from a tire, consonant with the intellectual field devices, 1 channel, faultlocation of chain, SIL 2 (1 yr) D1030D ; Repet of the state of pin sensor/of sensor of position with a relay exitом, 2 channelа, 2 relay exitа SPDT D1030D/B ; Repet of the state of pin sensor/of sensor of position with a relay exitом, 2 channelа, 2 relay exitа SPDT D1030D-018 ; Repeat the states of sensor of position, 2 channelа, 2 relay exitа SPDT D1030D-018/B ; Repeat the states of sensor of position, 2 channelа, 2 relay exitа SPDT D1030S ; Repet of the state of pin sensor/of sensor of position with a relay exitом, 1 channel, 1 relay exit SPDT D1030S/B ; Repet of the state of pin sensor/of sensor of position with a relay exitом, 1 channel, 1 relay exit SPDT D1030S-018 ; Repeat the states of pin sensor, 1 channel, 1 relay exit DPDT или 2 exitа SPDT D1030S-018/B ; Repeat the states of pin sensor, 1 channel, 1 relay exit DPDT или 2 exitа SPDT D1031D ; Repet of the state of pin sensor/of sensor of position, 2 channelа, 4 exitа type open collector, 1 КГц D1031D/B ; Repet of the state of pin sensor/of sensor of position, 2 channelа, 4 exitа type open collector, 1 КГц D1031Q ; Repet of the state of pin sensor/of sensor of position, 4 channelа, 4 exitа type open collector, 1 КГц D1031Q/B ; Repet of the state of pin sensor/of sensor of position, 4 channelа, 4 exitа type open collector, 1 КГц D1032D ; Will repeat the states of pin sensor/of sensor of position, 2 isolated channelа, 4 relay exitа SPST, signaling of damage to the line, SIL 2 (5 yr) D1032D/B ; Will repeat the states of pin sensor/of sensor of position, 2 isolated channelа, 4 relay exitа SPST, signaling of damage to the line, SIL 2 (5 yr) D1032Q ; Repet of the state of pin sensor/of sensor of position, 4 isolated channelа, 4 relay exitа SPST, signaling of damage to the line, SIL 2 (5 yr) D1032Q/B ; Repet of the state of pin sensor/of sensor of position, 4 isolated channelа, 4 relay exitа SPST, signaling of damage to the line, SIL 2 (5 yr) D1033D ; Repet of the state of pin sensor/of sensor of position, 2 isolated channelа, 4 exitа type open collector, signaling of damage to the line, SIL 2 (5 yr) D1033D/B ; Repet of the state of pin sensor/of sensor of position, 2 isolated channelа, 4 exitа type open collector, signaling of damage to the line, SIL 2 (5 yr) D1033D-052 ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 2 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Negative D1033D-052/B ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 2 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Negative D1033D-058 ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 2 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Positive D1033D-058/B ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 2 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Positive D1033Q ; Repet of the state of pin sensor/of sensor of position, 4 isolated channelа, 4 exitа type open collector, signaling of damage to the line, SIL 2 (5 yr) D1033Q/B ; Repet of the state of pin sensor/of sensor of position, 4 isolated channelа, 4 exitа type open collector, signaling of damage to the line, SIL 2 (5 yr) D1033Q-052 ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 4 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Negative D1033Q-052/B ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 4 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Negative D1033Q-058 ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 4 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Positive D1033Q-058/B ; Repet of the state of pin sensor/of sensor of position with a transistor exitом, Digital Input, 4 Ch., 4 OC Transis. Outputs SPST, Line Fault Detection, SIL 2 (5yr) Common Positive D1034D ; Repeat signal of sensor of position or pin sensor, 2 channelа, повышенная отказаоустойчивость, SIL 3 (1 yr)/SIL 2 (10 yr) D1034D/B ; Repeat signal of sensor of position or pin sensor, 2 channelа, повышенная отказаоустойчивость, SIL 3 (1 yr)/SIL 2 (10 yr) D1034S ; Repeat signal of sensor of position or pin sensor, 1 channel, enhanceable faulttolerance, SIL 2 (10 yr) D1034S/B ; Repeat signal of sensor of position or pin sensor, 1 channel, enhanceable faulttolerance, SIL 2 (10 yr) D1035S ; Repeat with a galvanic upshot for frequency/impulsive signals D1035S/B ; Repeat with a galvanic upshot for frequency/impulsive signals D1040Q ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, Imax =74 мА, 334 Ом, SIL 3 (LP)/SIL 2 (BS) D1040Q/B ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, Imax =74 мА, 334 Ом, SIL 3 (LP)/SIL 2 (BS) D1041Q ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, с возможностью параллельного включения для управления by light-emitting diodes, Imax 74 mA, SIL 3 (LP)/SIL 2 (BS) D1041Q/B ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, с возможностью параллельного включения для управления by light-emitting diodes, Imax 74 mA, SIL 3 (LP)/SIL 2 (BS) D1042Q ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, Imax 88,2 мА, 273 Ом, SIL 3 (LP)/SIL 2 (BS) D1042Q/B ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, Imax 88,2 мА, 273 Ом, SIL 3 (LP)/SIL 2 (BS) D1043Q ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, с возможностью параллельного включения для управления соленоидами, Imax =49,6 мА, 455 Ом, SIL 3 (LP)/SIL 2 (BS) D1043Q/B ; Driver with digital exitом for a management by solenoids, by light-emitting diodes, by voice Warners, 4 channelа, с возможностью параллельного включения для управления соленоидами, Imax =49,6 мА, 455 Ом, SIL 3 (LP)/SIL 2 (BS) D1044D ; Module with relay exitом, 2 Channels, 2 SPDT Relays to Hazardous Location D1044S ; Module with relay exitом, 1 Channel, 1 SPDT Relay to Hazardous Location D1045Y ; Driver with digital exitом for a management by solenoids, Digital outputs, 2 channels for solenoids ATOS 283/249 mA max., 69/79 Ohm D1045Y/B ; Driver with digital exitом for a management by solenoids, Digital outputs, 2 channels for solenoids ATOS 283/249 mA max., 69/79 Ohm D1046Y ; Driver with digital exitом for a management by solenoids, Digital outputs, 2 channels for solenoids WANDFLUH 362 mA max., 68 Ohm D1046Y/B ; Driver with digital exitом for a management by solenoids, Digital outputs, 2 channels for solenoids WANDFLUH 362 mA max., 68 Ohm D1048S ; Driver with digital exitом for a management by solenoids, Digital Output, 1 Channel NE Loads, Loop Powered, Line & Valve Monitoring, Selectable Out., SIL 3 (L. T.) D1048S/B ; Driver with digital exitом for a management by solenoids, Digital Output, 1 Channel NE Loads, Loop Powered, Line & Valve Monitoring, Selectable Out., SIL 3 (L. T.) D1049S ; Driver with digital exitом for a management by solenoids, Digital Output, 1 Channel NE Loads, BUS Powered, Line & Valve Monitoring, Selectable Out. SIL 3 (2 yr) D1049S/B ; Driver with digital exitом for a management by solenoids, Digital Output, 1 Channel NE Loads, BUS Powered, Line & Valve Monitoring, Selectable Out. SIL 3 (2 yr) D1052D ; Transformer of analog signals, 2 channelа, exit мA / В, programming by means of PC and adapter PPC1092, SIL 2 (5 yr) D1052D/B ; Transformer of analog signals, 2 channelа, exit мA / В, programming by means of PC and adapter PPC1092, SIL 2 (5 yr) D1052S ; Transformer of analog signals, 1 channel, exit мA/В, programming by means of PC and adapter PPC1092, SIL 2 (5yr) D1052S/B ; Transformer of analog signals, 1 channel, exit мA/В, programming by means of PC and adapter PPC1092, SIL 2 (5yr) D1052X ; Transformer of analog signals, 1 entrance / 2 isolated exitа мA/В, programming by means of PC and adapter PPC1092 D1052X/B ; Transformer of analog signals, 1 entrance / 2 isolated exitа мA/В, programming by means of PC and adapter PPC1092 D1052Y ; Transformer of analog signals, 2 entrance - exit isolated channelа мA/В, селектор H-L, programming by means of PC and adapter PPC1092 D1052Y/B ; Transformer of analog signals, 2 entrance - exit isolated channelа мA/В, селектор H-L, programming by means of PC and adapter PPC1092 D1053S ; Transformer of analog signals, 1 channel, entrance мA-В, exit мА-В + 2 threshold level, programmable through PPC1092, SIL 2 ( 1 yr) D1053S/B ; Transformer of analog signals, 1 channel, entrance мA-В, exit мА-В + 2 threshold level, programmable through PPC1092, SIL 2 ( 1 yr) D1053S-021 ; Transformer of analog signal and threshold strengthener, 1 channel entrance-exit, mA-V, + 2 threshold exitа, fully programmable, SIL 2 (1 yr), 10 Vdc PS D1053S-021/B ; Transformer of analog signal and threshold strengthener, 1 channel entrance-exit, mA-V, + 2 threshold exitа, fully programmable, SIL 2 (1 yr), 10 Vdc PS D1054S ; Transformer of analog signal and threshold strengthener, 1channel, Smart, active-passive entrance, an exit is a source-receiver of current, +2 threshold exitа, programmable through PPC1092, SIL 2 (5 yr) D1054S/B ; Transformer of analog signal and threshold strengthener, 1channel, Smart, active-passive entrance, an exit is a source-receiver of current, +2 threshold exitа, programmable through PPC1092, SIL 2 (5 yr) D1060S ; Transformer of frequency signal, 1 channel entranceной signal до 50 кГц, 1 analog exit мА-В, + 2 threshold level. Scaling coefficient of exitного signal 1, 10, 100, 1000, 10000, 100000, 1000000. programming by means of PC and adapter PPC1092 D1060S/B ; Transformer of frequency signal, 1 channel entranceной signal до 50 кГц, 1 analog exit мА-В, + 2 threshold level. Scaling coefficient of exitного signal 1, 10, 100, 1000, 10000, 100000, 1000000. programming by means of PC and adapter PPC1092 D1060S/V ; Преобразователь частотных cигналов, 1 канал входной сигнал: 0- 500 Гц, 1 аналоговый выход: 4-20 мА. D1060S-049 ; Transformer of frequency signal, 1 channel entranceной signal до 50 кГц, 1 analog exit мА-В, + 2 threshold level. Scaling coefficient of exitного signal 1, 10, 100, 1000, 10000, 100000, 1000000. Специальное исполнение с фиксирующими диодами. Прог D1061S ; Insulating repeat for the serial interface of type RS422/RS485, speed of transmission 1.5 Мбит/сек. entrance: RS485, RS422 - exit: RS422, RS232 D1061S/B ; Insulating repeat for the serial interface of type RS422/RS485, speed of transmission 1.5 Мбит/сек. entrance: RS485, RS422 - exit: RS422, RS232 D1061S-077 ; Insulating repeat for the serial interface of type RS422/RS485, speed of transmission 1.5 Мбит/сек. entrance: RS485, RS422 - exit: RS422, RS232, Lower Safety Parameters D1062S ; Module of transformation of signalов from vibro-pickups Vibration Monitor Sensors Isolated Interface, SIL 2 (1 yr), Input from Bentley Nevada, BK & Vibrometer Sensors D1063S ; Transformer with a galvanic upshot for tenzometrical bridge, entrance: to 4 - x of in-parallel cells by resistance 350 Ohm, loading ability :: 5В, 80 мА D1063S/B ; Transformer with a galvanic upshot for tenzometrical bridge, entrance: to 4 - x of in-parallel cells by resistance 350 Ohm, loading ability :: 5В, 80 мА D1064S ; Transformer with a galvanic upshot for tenzometrical bridge, Input for Up to 4 parallel cells 350 Ohm, 5V, 80 mA total capability, D1072D ; Transformer of signal from the sensor of temperature, 2 channelа TC-RTD-Tx Pot, 2 exitа мA-В, programmable through PPC1092, (X & Y Function), SIL 2 (1 yr) D1072D/B ; Transformer of signal from the sensor of temperature, 2 channelа TC-RTD-Tx Pot, 2 exitа мA-В, programmable through PPC1092, (X & Y Function), SIL 2 (1 yr) D1072D-024 ; Transformer of signal from the sensor of temperature, Temperature Converter, 2 Input / Output Ch. 0-80 or 16-80 mV range, Fully Programmable D1072D-024/B ; Transformer of signal from the sensor of temperature, Temperature Converter, 2 Input / Output Ch. 0-80 or 16-80 mV range, Fully Programmable D1072D-028 ; Transformer of signal from the sensor of temperature, Temperature Converter, 2 Input / Output Ch. According APN0008 D1072D-028/B ; Transformer of signal from the sensor of temperature, Temperature Converter, 2 Input / Output Ch. According APN0008 D1072D-059 ; Transformer of signal from the sensor of temperature Temperature Converter 2 Ch, TC-RTD-Tx Pot Input, mA-V Outputs, Fully Software Programmable, ( X & Y Function) D1072S ; Transformer of signal from the sensor of temperature, 1 channel TC-RTD-Tx Pot, 1 exit мA-В, programmable through PPC1092, SIL 2 (1 yr) D1072S/B ; Transformer of signal from the sensor of temperature, 1 channel TC-RTD-Tx Pot, 1 exit мA-В, programmable through PPC1092, SIL 2 (1 yr) D1072S-024 ; Transformer of signal from the sensor of temperature, Temperature Converter, 1 Input / Output Ch. 0-80 or 16-80 mV range, Fully Programmable D1072S-024/B ; Transformer of signal from the sensor of temperature, Temperature Converter, 1 Input / Output Ch. 0-80 or 16-80 mV range, Fully Programmable D1073S ; Transformer of signal from the sensor of temperature, 1 channel. entrance TC / RTD / Tx Pot, 1 exit мA / В + 2 threshold level programmable through PPC1092, SIL 2 (1 yr) D1073S/B ; Transformer of signal from the sensor of temperature, 1 channel. entrance TC / RTD / Tx Pot, 1 exit мA / В + 2 threshold level programmable through PPC1092, SIL 2 (1 yr) D1073S-032 ; Transformer of signal from the sensor of temperature Temperature Converter, 1 Ch. TC-RTD-Tx Pot IN, mA / V OUT + 2 Trip Amp, Fully Software Program, SIL 2 (1 yr), 10 Vdc D1073S-032/B ; Transformer of signal from the sensor of temperature Temperature Converter, 1 Ch. TC-RTD-Tx Pot IN, mA / V OUT + 2 Trip Amp, Fully Software Program, SIL 2 (1 yr), 10 Vdc D1080D ; Interface for the sensors of presence of steams of combustible liquids, 2 relay exitа SPDT, intended for 3th wire probes D1081D ; Interface for the sensors of presence of steams of combustible liquids, 2 channelа type open collector, intended for 3th wire probes D1090Q ; Module with by shunts 4 Channels Shunt Module for mA inputs of D2010 & D2011 Units D1091S ; Module an emergency, Common Alarm Module for D1000 Series with Fault Output, 1 SPDT Relay Output D1092D ; Module with relay exitом, 2 Ch, SIL 3 Relay, Out: N° 4 SPST NO Relay two for NE Loads & two for ND Loads. SIL 3 (20Yr) D1092D-069 ; Module with relay exitом, 2 Ch, SIL 3 Relay, Out: N° 4 SPST NO/NC Relay two for NE Loads & two for ND Loads. SIL 3 (20Yr) D1092S ; Module with relay exitом, 1 Ch, SIL3 Relay, Out: N° 2 SPST NO Relay one for NE Loads & one for ND Loads. SIL 3 (20Yr) D1092S-069 ; Module with relay exitом, 1 Ch, SIL3 Relay, Out: N° 2 SPST NO/NC Relay one for NE Loads & one for ND Loads. SIL 3 (20Yr) D1093S ; Module with relay exitом, 1 Ch, SIL3 Relay, Out: N° 2 SPST NO Relay one for NE Loads & one for ND Loads. SIL 3 (20Yr), with Line and Load Breakage Detection D1094Q ; Module with by shunts 4 Channels Shunt Module for V inputs of D2010 & D2011 Units D1130D ; Repet of signal of sensor of approaching, 2 channelа, 2 relay exitа SPDT D1130S ; Repet of the state of pin sensor/of sensor of position with a relay exitом, Digital Input, 1 Channel, 2 Relay Outputs SPDT or 2 outputs SPDT - 110-220 Vac D1180D ; Interface for the sensor of presence of steams of combustible liquids, 2 relay exitа SPDT, intended for 3th wire probes D2010M ; spark safe мульт плексор with 16 аналого-температурными entranceными channelами, set in a dangerous area, used with the sluice of D2050. D2011M ; spark safe 16 - channel аналого-температурный module of expansion for multplecsora D2010M, set in a dangerous area. Editing on DIN- to the lath D2030M ; spark safe мультплексор with 32 digital entranceными channelами, set in a dangerous area, used with the sluice of D2050Монтаж on DIN- to the lath. To 4 modules of D2030M are connected to the sluice of D2050 D2050M ; Interinterface sluice and Source of feed for 4 multiplexer modules of D2010 - 2030, Editing on DIN- to the lath, in a safe zone. Reserved of communication line of RS485, protocol of RTU Modbus D2052M ; exitной repeat with 32 relayи exitами for digital multplecsora D2030М D2053M ; exitной repeat from 32 transistor exitами for multplecsora D2030М D5000D ; Empty module Dummy module with Hazardous Area Terminal blocks, 12 mm D5011D ; Module spark safe 2 Independent Ch, 4-20 mA 2 Wire IN, 4-20 mA Source OUT, HART, SIL 3 (1 yr)/SIL 2 (10 yr) D5011S ; Module spark safe 1 Ch, 4-20 mA 2 Wire IN, 4-20 mA Source OUT, HART, SIL 3 (1 yr)/SIL 2 (10 yr) D5014D ; Module spark safe 2 Independent Ch, 0/4-20 mA, 2/3 Wire IN, mA/V Sink/Source OUT, HART, SIL 3 (1 yr)/SIL 2 (10 yr) D5014S ; Module spark safe 1 Ch, 0/4-20 mA, 2/3 Wire IN, mA/V Sink/Source OUT, HART, SIL 3 (1 yr)/SIL 2 (10 yr) D5020D ; Module spark safe 2 Independent Ch, Smart-Hart, Isolating Driver for I/P, 0/4-20 mA IN-OUT, SIL 2 (1 yr) D5020S ; Module spark safe 1 Ch, Smart-Hart, Isolating Driver for I/P, 0/4-20 mA IN-OUT, SIL 2 (1 yr) D5030D ; Module spark safe 2 Independent Ch, 2 SPST Relay Output, Line Monitoring Function, SIL 3 (2 yr)/SIL 2 (20 yr) D5030S ; Module spark safe 1 Ch, 1 SPDT Relay Output, Line Monitoring Function, SIL 3 (2 yr)/SIL 2 (20 yr) D5031D ; Module spark safe 2 Independent Ch, 2 NO/NC Solid State Out, Line Monitoring Function, SIL 3 (2 yr)/SIL 2 (20 yr) D5031S ; Module spark safe 1 Ch, 1 NO/NC Solid State Output, Line Monitoring Function, SIL 3 (2 yr)/SIL 2 (20 yr) D5032D ; Module spark safe 2 Independent Ch, 2 SPST Relay Outputs, Line Monitoring Function, SIL 3 (2 yr)/SIL 2 (20 yr) D5032S ; Module spark safe 1 Ch, 1 SPDT Relay Output, Line Monitoring Function, SIL 3 (2 yr)/SIL 2 (20 yr) D5034D ; Module spark safe 2 Independent Ch, Transparent to Contact-Proximity & Line Monitoring Function, SIL 3 (1 yr)/SIL 2 (10 yr) D5034S ; Module spark safe 1 Ch, Transparent to Contact-Proximity & Line Monitoring Function, SIL 3 (1 yr)/SIL 2 (10 yr) D5048S ; Module spark safe 1 Ch, Solenoid Driver, Loop Powered, Transparent Line & Load Alarm Function, SIL 3 (20 yr) D5049S ; Module spark safe 1 Ch, Solenoid Driver, Bus Powered, Transparent Line & Load Alarm Function, SIL 3 (1 yr) D5072D ; Transformer of signal from the sensor of temperature 2 Ch, TC-RTD-Tx Pot Input, mA-V Outputs, Fully Programmable, SIL 2 (5 yr) D5072S ; Transformer of signal from the sensor of temperature 1 Ch, TC-RTD-Tx Pot Input, mA-V plus Burnout Alarm Outputs, Fully Programmable, SIL 2 (5 yr) D5072S-087 ; Преобразователь сигнала с датчика температуры 1 Ch, RTD Input, RTD Output, SIL 2 (5 yr) D5090S ; Relay 1 Ch, SIL3 Relay for NE Load, SPDT NC 4 Amps OUT plus Service OUT, SIL 3 (10 Yr)/SIL 2 (20yr) D5090S-086 ; Релейный модуль одноканальный 1, SIL3 Relay for NE Load, SPDT NC 4 Amps OUT plus Service OUT, SIL 3 (10Yr) / SIL 2 (20yr) 1 Ch, SIL3 Relay for NE Load, SPDT NC 4 Amps OUT plus Service OUT, SIL 3 (10Yr) / SIL 2 (20yr) D5091S ; Relay 1 Ch, SIL3 Relay for ND Load, SPDT NO 4 Amps OUT plus Service OUT, SIL 3 (6 Yr)/SIL 2 (20yr) D5200D ; Empty module Dummy module with Hazardous Area Terminal blocks, 22 mm D5202S ; Модуль аварийной сигнализации Redundant Power Connection & Common Alarm Module (SPST) for D5/6000 Series, Max 4 Amps D5231E ; Module spark safe 8 Ch, NO/NC Solid State Output, Line Monitoring Function, SIL 2 D5254S ; Модуль искробезопасный одноканальный, Smart-Hart, 0/4-20 mA Input, mA-V Output + 2 Trip Amp, Fully Softw. Program, SIL 2 (5 yr) D5273S ; Преобразователь сигнала с датчика температуры искробезопасный 1 Ch, TC-RTD-Tx Pot Input, mA-V Outputs, + 2 Trip Amplifiers, Fully Programmable, SIL 2 (5 yr) D5290S ; Relay 1 Ch, SIL3 Relay for NE Load, SPDT NC 10 Amps OUT plus Service OUT, SIL 3 (10 Yr)/SIL 2 (20yr) D5290S/SA ; Relay 1 Ch, SIL3 Relay for NE Load, SPDT NC 10 Amps OUT plus Service OUT, SIL 3 (10Yr) / SIL 2 (20yr) D5290S-078 ; Relay 1 Ch, SIL3 Relay for NE Load, 2 NC 3 Amps OUT plus Service OUT, SIL 3 (10 Yr)/SIL 2 (20yr) D5290S-078/SA ; Реле одноканальное, SIL3 Relay for NE/ND Load, 2 NC / 3 NO 5 Amps OUT, SIL 3 (10Yr) / SIL 2 (20yr) D5290S-079 ; Relay 1 Ch, SIL3 Relay for NE Load, 2 NC 4 Amps OUT/110Vac Coil, SIL 3 (10 Yr)/SIL 2 (20yr) D5290S-080 ; Relay 1 Ch, SIL3 Relay for NE Load, 2 NC 4 Amps OUT / 110Vac Coil , SIL 3 (10Yr) / SIL 2 (20yr) D5290S-084 ; Реле одноканальное, SIL3 Relay for NE Load, 2 NC 5 Amps OUT / 115Vdc Coil , SIL 3 (10Yr) / SIL 2 (20yr) D5291S ; Relay 1 Ch, SIL3 Relay for ND Load, SPDT NO 10 Amps OUT plus Service OUT, SIL 3 (6 Yr)/SIL 2 (20yr) D5293S ; Relay 1 Ch, SIL3 Relay for NE Load, SPST NC 10 Amps OUT plus Fault OUT, SIL 3 (10 Yr)/SIL 2 (20yr) D5294S ; Relay 1 Ch, SIL2 Relay for ND Load, 2 x SPST NO 10 Amps OUT plus Fault OUT, SIL 3 (7 Yr)/SIL 2 (20yr) D6000D ; Пустой модуль Dummy module with Field & Control Room Terminal blocks, 12 mm D6011D ; Модуль нормализатора сигнала с гальванической развязкой 2 Independent Ch, 4-20 mA 2-Wire IN, 4-20mA Source OUT, Hart, SIL 3 (1yr) / SIL 2 (10yr) D6011S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, 4-20 mA 2-Wire IN, 4-20mA Source OUT, Hart, SIL 3 (1 yr) / SIL 2 (10yr) D6014D ; Модуль нормализатора сигнала с гальванической развязкой 2 Independent Ch, 0/4-20 mA, 2/3-Wire IN, mA/V Sink/Source OUT, Hart, SIL 3 (1 yr) / SIL 2 (10yr), Unit is field configurable as Duplicator 1 IN - 2 OUTs D6014S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, 0/4-20 mA, 2/3-Wire IN, mA/V Sink/Source OUT, Hart, SIL 3 (1 yr) / SIL 2 (10yr) D6020D ; Модуль нормализатора сигнала с гальванической развязкой 2 Independent Ch, 4-20 mA, I/P Driver, Transparent Open-Short Circuit Alarm Function, SIL2 (3 yr), Unit is field configurable as Duplicator 1 IN - 2 OUTs D6020S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, 4-20 mA, I/P Driver, Transparent Open-Short Circuit Alarm Function, Hart SIL 2 (3 yr) D6030D ; Модуль нормализатора сигнала 2 Independent Ch, 2 SPST Relay Outputs, Line Monitoring Function, SIL 3 (2 yr) / SIL 2 (20yr), Unit is field configurable as Duplicator: 1 IN / 2 OUTs or 1 IN - 1+1 OUT (DI + LMF) D6030S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, 1 SPDT Relay Output, Line Monitoring Function, SIL 3 (2 yr) / SIL 2 (20yr) D6031D ; Модуль нормализатора сигнала с гальванической развязкой 2 Independent Ch 2 NO/NC Transistor Out, Line Monitoring Function, SIL 3 (2 yr) / SIL 2 (20yr) D6031S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, 1 NO/NC Solid State Output, Line Monitoring Function, SIL 3 (2 yr) / SIL 2 (20yr) D6072D ; Модуль нормализатора сигнала с гальванической развязкой 2 Ch, TC-RTD-Tx Pot Input, mA-V Outputs, Fully Programmable, SIL 2 (5 yr), Unit is field configurable as Duplicator 1 IN - 2 OUT D6072S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, TC-RTD-Tx Pot Input, mA-V plus Burnout Alarm Outputs, Fully Programmable, SIL 2 (5 yr) D6072S-087 ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, RTD Input, RTD Output, SIL 2 (5 yr) D6200D ; Пустой модуль Dummy module with Field & Control Room Terminal blocks, 22 mm D6231E ; Модуль нормализатора сигнала с гальванической развязкой 8 Ch, NO/NC Solid State Output, Line Monitoring Function, SIL 2 D6254S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, Smart-Hart, 0/4-20 mA Input, mA-V Output + 2 Trip Amp, Fully Softw. Program, SIL 2 (5 yr) D6273S ; Модуль нормализатора сигнала с гальванической развязкой 1 Ch, TC-RTD-Tx Pot Input, mA-V Outputs, + 2 Trip Amplifiers, Fully Programmable, SIL 2 (5 yr) GM2320-SS-20-NB-M20 ; Corps Stainless Steel Enclosure, For installation of N° 1 D2010M Module Dim.: 400x400x200 mm. With a total of N° 16 M20-DN07 + N° 4 M20-DN1.1 Nichel Plated Brass Cable Glands. Net weight 10,5 Kgs. Suitable for N° 1 - D2010M module GM2320-SS-36-NB-M20 ; Corps Stainless Steel Enclosure, For installation of N° 1 D2030M Module.Dim.: 400x400x200 mm. With a total of N° 32 M20-DN07 + N° 4 M20-DN1.1 Nichel Plated Brass Cable Glands. Net weight 12,0 Kgs.Suitable for N° 1 - D2030M module GM2330-SS-36-NB-M20 ; Corps Stainless Steel Enclosure, For installation of N2 D2010M or N1 D2011M & N1 D2011M Modules Dim.: 600x400x200 mm. With a total of N32 M20-DN07 + N4 M20-DN1.1 Nichel Plated Brass Cable Glands. Net weight 17,0 Kgs. GM2330-SS-52-NB-M20 ; Corps Stainless Steel Enclosure, For installation of N° 1 D2010M & N° 1 D2030M Modules or N° 1 D2010M & N° 2 D2011M Mod.Dim.: 600x400x200 mm. With a total of N° 48 M20-DN07 + N° 4 M20-DN1.1 Nichel Plated Brass Cable Glands. Net weight 20,0 Kgs GM2330-SS-68-NB-M20 ; Corps Stainless Steel Enclosure, For installation of N° 4 D2010M / D2011M or N° 2 D2030M Modules.Dim.: 600x400x200 mm. With a total of N° 64 M20-DN07 + N° 4 M20-DN1.1 Nichel Plated Brass Cable Glands. Net weight 20,0 Kgs JDFT049 ; Connector 12 mm Power Bus Connector for DIN Rail Maonting, One needed for each BUS Module JDFT050 ; Connector 22 mm Power Bus Connector for DIN Rail Maunting, One needed for each BUS Module LABL011 ; Маркировка Front Label Blue Colour (RAL5015), Page of 60 pcs LABL012 ; Маркировка Front Label Grey Colour (RAL7042), Page of 60 pcs MCHP 061/3 ; Empty module, Dummy Bus module with Bus connector removed MCHP 064 ; Marking, Tagplate in policarbonate material MCHP 065 ; Protective gib for fixing of the modules on DIN to the lath MCHP 090 ; A sticker marking, A4 sheet with 72 mylar white lables for tagging. Software for tags compilation available on GMI web site free of charge MCHP 139 ; Delimiter, 5 mm separator for modules MCHP044 ; Корпус пластмассовый Main Case D1000 Series Gray RAL7031 (LASER D1061S) MCHP061 ; Корпус пластмассовый D1000 Serie BUS Enclosure Gray MCHP183 ; Terminal block Blue Terminal Block Plug 12 mm MCHP184 ; Terminal block Grey Terminal Block Plug 12 mm MCHP185 ; Terminal block Blue Terminal Block Plug 22 mm MCHP186 ; Terminal block Grey Terminal Block Plug 22 mm MCHP196 ; Clamp Bus End Stopper, One for each end of Bus Required MOR 010 ; A block is a terminal grey color, Grey Terminal Block Laser Engraved: 1-2-3-4 MOR 015 ; I will eat away the tires of feed POWER BUS with vertical connection,(shtecer) MOR 016 ; Clamp of DIN of lath MOR 017 ; I will eat away the tires of feed POWER BUS with horizontal connection MOR 022 ; I will eat away the tires of feed POWER BUS with horizontal connection,(wall outlet) MOR 046/2 ; Block a terminal for APN005: passive exit for D1052*/D1053*/D1072* MOR 058 ; Блок терминальный Terminal Block for PLC Pulse Damping of D109X relay MOR045 ; Double terminal block for connection of communication cable of CABF008 MOR051 ; Блок соединителей 2.5mm Terminal Block 2p, Blue Color (RAL5015), Number Marking to be specified MOR052 ; Блок соединителей 2.5mm Terminal Block 2p, Gray Color (RAL7042), Number Marking to be specified OPT1091 ; Scray of cold shut OPT1096 ; Complete set assembling. Kit For Bus Mounting Include: N° 2 MOR016, N° 1 MOR017, N° 1 MOR022, N° 2 MCHP065. One needed for each group of modules OPT1097 ; Complete set assembling Kit For Bus Mounting Include: N° 1 MOR015, N° 1 MOR022, N° 2 MCHP065 OPT2091 ; Scray of of cold shut thermocouples, assembled on the entranceных terminals of the modules. OPT2094 ; Complete set for editing of corps GM 2300 на стенку Wall Mounting KIT for GM 2300 Series Enclosures OPT2095 ; Complete set for editing on a door Front Door Mounting KIT for GM 2300 Series Enclosures OPT3092 ; Complete set assembling Stainless Steel Bracket set and Gasket for Flush-Panel Mounting OPT3093 ; Complete set assembling, Stainless Steel Bracket set for 50-70 mm pipe Mounting and OPT5096 ; Complete set assembling Kit For Bus Mounting Include: N 1 MOR017, N1 MOR022, N2 MCHP196 PBCO-D01-041 ; Pay assembling 1 Hart MUX Module / 32 Channels Board for ABB TC-200 System PBCO-D04-038 ; Pay assembling 4 Module / 8 Channels DI Board for ABB TC-200 System PBCO-D04-039 ; Pay assembling 4 Module / 4 Channels DO Board for ABB TC-200 System PBCO-D04-040 ; Pay assembling 4 Module / 8 Channels AI Board for ABB TC-200 System with Hart PBCO-D08-047 ; Pay assembling 16 AI Ch. Board suitable for Cards SAI 143 16 AI Ch. each PBCO-D08-048 ; Pay assembling 16 DI Ch. Board suitable for Card SDV 144 - 16 DI Ch. each PBCO-D08-049 ; Pay assembling 8 DO Ch. Board suitable for card SDV 531 - 8 DO Ch. each PBCO-D08-051 ; Pay assembling AI Board for 8 Analogue Inputs, for AI 845 Card and for 16 Channel Analogue Inputs PBCO-D08-052 ; Pay assembling AO Board for 8 Analogue Outputs, for AO 845 Card and for 16 Channel Analogue Outputs PBCO-D08-053 ; Pay assembling DI Board for 16 Digital Inputs, for DI 810 Card or for 32 Channel Digital Inputs PBCO-D12-008 ; Pay assembling Analog Board for 12 Double Analog modules, for A-Loop IOB Card suitable for 16 Analog Input and 8 Analog Output channels PBCO-D16-012 ; Pay assembling 32 AI Ch. Board + Hart connector suitable for TMR 3704 E (Each TMR requires 2 Boards) PBCO-D16-013 ; Pay assembling 32 DI Ch. Board suitable for TMR 3503E, 3505E PBCO-D16-015 ; Pay assembling 32 DI Ch. Board suitable for TMR 3504 A (Each TMR requires 2 Boards) PBCO-D16-021 ; Pay assembling 16 Modules Board for IOP, HLAI, CC, P/N 51304754-150 PBCO-D16-022 ; Pay assembling 16 Modules Board for IOP, A/O, CC, P/N 51309152-175 PBCO-D16-023 ; Pay assembling 16 Modules Board for IOP, DI, CC, P/N 51304485-150 PBCO-D16-024 ; Pay assembling 16 Modules Board for IOP, DO, CC, P/N 513044485-150 PBCO-D16-025 ; Pay assembling 16+16 AI Ch. Board suitable for Cards AAI 141- 16+16 AI ch. each PBCO-D16-026 ; Pay assembling 16 + 16 AO Ch. Board suitable for card AAI 543 - 16 +16 AO Ch. each PBCO-D16-027 ; Pay assembling 32+32 DI Ch. Board suitable for card ADV 151 - 32+32 DI (using 16 four ch. Module) PBCO-D16-035 ; Standard pay for series D1000: 16 AI or 16 AO with standard ELCON 56 Pin Output Connector PBCO-D16-036 ; Standard pay for series D1000: 32 AI or 32 AO + HART Connector with 2 standard ELCON 56 Pin Output Connectors PBCO-D16-037 ; Standard pay for series D1000: 32 AI or 32 AO + HART Multiplexer Ready with Terminal Block output PBCO-D16-042 ; Pay assembling 32 AI Ch. Board + Hart connector suitable for TMR 3700 A PBCO-D16-043 ; Pay assembling 32 DI Ch. Board suitable for TMR 3503 E PBCO-D8-001 ; Pay assembling Analog Board for 6 Double Analog modules, for A-Loop IOB Card suitable for 8 Analog Input and 4 Analog Output channels PBCO-D8-002 ; Pay assembling Digital Board for 8 four channel Digital Input modules, for A-Loop IOB & D-Loop IOB Card suitable for 32 input channels PBCO-D8-009 ; Pay assembling 16 Ch. Board: 16 AI or 8 DI + 8 DO or 16 DI or 16 DO suitable for FBM 211, 241, 242, 207 single connector PBCO-D8-010 ; Pay assembling 8 Ch. Board: 8 AO or 8 AI or 4AO + 4AI suitable for FBM 237, 201, 204, 205 single or redundant connector PBCO-D8-011 ; Pay assembling 32 Ch. Board: 32 DI suitable for FBM 217 single connector PBCO-D8-014 ; Pay assembling 8 Ch. Board AO + Hart connector, suitable for TMR 3805E PBCO-D8-032 ; Standard pay for series D1000: 32 DI or 32 DO or 16AI or 16 AO + HART Connector with standard ELCON 56 Pin PBCO-D8-033 ; Pay assembling 16 AI + 16 AO or 32 DI + Hart connector suitable for DeltaV PBCO-D8-044 ; Standard pay for series D1000: 16 Ch (8 Modues) with Terminal Block output PBCO-D8-050 ; Standard pay for the modules of series D1000: 8/16 + 8/16 AI, AO, DI or DO Board + HART Connector with standard ELCO Out. Connector PPC1090 ; Compact configurator required for the programmable modules PPC1092 ; Adapter of serial port for programming of the modules of series of D1000 with the cable of CABF010, required when PC is used instead of PPC1090 PPC2094 ; Demo-Complete Optional Kit for System Demo Via RS-485 Modbus & RS-232 Serial Port PPC2095 ; Demo-Complete Optional Kit for System Demo Via RS-232 Serial Port only PPC5092 ; Adapter USB для конфигурирования серии D5000: PC Adapter required to configure programmable units, Mini USB Male to USB Ports PSD1000 ; Source of feed Zone 2 Power Supply, II 3 G Eex nA IIC T4, exit 24 V/0,6 A, for the feed of the modules of series of D1000 from the network of alternating current PSD1000/B ; Universal impulsive source of feed, entrance 115-230 In application current(possibly 90-264 В), frequency from 48 to 400 Hertzs, or 120-370 In direct-current, exit 24 In/0,5 A PSD1000/F ; Source of feed Zone 2 Power Supply, II 3 G Eex nA IIC T4, exit 24 V/0,6 A, for the feed of the modules of series of D1000 from the network of alternating current с формированием signalа тревоги PSD1001 ; Source of feed 4 channel, marking of implosion protection [EEx ia] IIC, exitная power 15 В, 20 мA на channel. PSD1001/B ; Source of feed 4 channel, marking of implosion protection [EEx ia] IIC, exitная power 15 В, 20 мA на channel. PSD1001C ; Source of feed 1 channel, marking of implosion protection [EEx ia] IIB, loading ability exitа 15 В, 140 мA, предназначен для питания оборудования находящегося во взрывоопасной зоне PSD1001C/B ; Source of feed 1 channel, marking of implosion protection [EEx ia] IIB, loading ability exitа 15 В, 140 мA, предназначен для питания оборудования находящегося во взрывоопасной зоне PSD1004 ; Source of feed spark safe, exit 5В/160 мА, feeds from PSD1001C, editing on DIN- lath, marking of implosion protection EEx ia IIB T4 PSD1210 ; Source of feed 1 channel, установка в зоне 2, entranceное tension 95-264 В перем. тока, exit 24В/10A (250 Вт), marking of implosion protection EEx nA IIC T4 PSU1003 ; Source of feed 1 channel spark safe, exit 5В/160 мА, feeds from PSD1001C, marking of implosion protection EEx ia IIB T4 T3010S ; spark safe indicator, with a feed from a contour, degree of defence of IP65, sizes are a 144х144х50 mm, a height of sign is a 20 mm, setting in a zone 1 TB D5012 INV 001 ; Pay assembling N° 12 / 12mm Modules N° 8 DI + N° 8 DO Board for FBM 241c Card, TB D5016-TRI-004 ; Плата монтажная N° 16 / 12mm Modules DI Board for TMR 3504E/3564 Card, Dual Channel Only TB-D5001-HRT-002 ; Плата монтажная N° 16/12 mm Modules AI-AO-DI-DO Board with ELCO 56 Pin Output + Hart Connectors TB-D5002-HRT-001 ; Плата монтажная N° 2 Hart Multiplexer Modules Support Board with N° 4 Flat Cable 34 Pins Connectors RS485 Output TB-D5008-ABB-001 ; N° 8 / 12mm Modules AI Board for AI810 & AI845 Cards via TU812 MTU, with Hart Conn. Curr. Out.AI 880 Board can be connected using Spliced cable with TU844 or TU845 MTU TB-D5008-ABB-002 ; N° 8 / 12mm Modules AO Board for AO810 & AO845 Cards via TU812 MTU, with Hart Connector TB-D5008-ABB-003 ; N° 8 / 12mm Modules AI Board for AI810 & AI845 Cards via TU812 MTU, with Hart Conn. Volt Out.AI 880 Board can be connected via TU812 (Termination Resistors Mounted on GMI Board) TB-D5008F-GMI-001 ; Pay assembling N° 8+2 (Fault)/12 mm Modules AI-AO-DI-DO Board + ELCO 56 Pin Output + Hart Connectors TB-D5008-GMI-001 ; Pay assembling N° 8/12 mm Modules AI-AO-DI-DO Board with ELCO 56 Pin Output + Hart Connectors TB-D5008-HON-001 ; Плата монтажная N° 8/ 12mm Modules Board for Safety Manager AO SAO-0220m Board TB-D5008-HON-002 ; Плата монтажная N° 8 / 12mm Modules Board for Safety Manager DO SDO-0824 Board TB-D5008-INV-001 ; Pay assembling N° 8 / 12mm Modules AI/DI Board for FBM 211 & FBM 207b Cards, With Hart Connector TB-D5008-INV-002 ; Pay assembling N° 8 / 12mm Modules AI/AO Board for FBM 201, 214b, 216b, 215, 218, 237 Cards, With Hart Conn. TB-D5008-INV-003 ; Плата монтажная N° 8 / 12mm Modules AI/AO Board for FBM 216, 218 Cards, With Hart Connector TB-D5008-SEI-001 ; Плата монтажная Termination Board 8 positions for 16 Analog Inputs or 16 Analog Outputs or 16 Temperature Inputs TB-D5008-TRI-001 ; Плата монтажная N° 8 / 12mm Modules AO Board for TMR 3805E Card, With Hart Connector TB-D5008-YOK-001 ; Pay assembling N° 8 / 12mm Modules DO Board for SDV 531 Card, TB-D5008-YOK-002 ; Pay assembling N° 8 / 12mm Modules AO Board for SAI 533 Card, TB-D5010-ICS-001 ; Pay assembling N° 10 / 12mm Modules AI Board 20 Channels Board with T8433 Card Connector TB-D5010-ICS-002 ; Pay assembling N° 20 / 12mm Modules DI Board 20 Channels Board with T8403 Card Connector TB-D5016-ABB-001 ; N° 16/12mm Modules DI/DO Board for DI810,DI830,D840, & DI880 + DO814 Cards via TU812 MTU TB-D5016-ABB-002 ; N° 16/12mm Modules DI/DO Board D0810, D840 & D0880 + DI814 Cards via TU812 MTU TB-D5016-GEB-001 ; Pay assembling N° 16 / 12mm Modules Universal 32 Channels Board with Card SUB-D and Hart Connectors TB-D5016-GMI-001 ; Pay assembling N° 16/12 mm Modules AI-AO-DI-DO Board with ELCO 56 Pin Output + Hart Connectors TB-D5016-HIM-001 ; Pay assembling N° 16/12 mm Modules AI-AO-DI-DO Board 16 Channels Master Board with HiMax and Hart Connector TB-D5016-HIM-002 ; Pay assembling N° 16/12 mm Modules AI-AO-DI-DO Board 16 Channels Slave Board with HiMax and Hart Connector TB-D5016-HIM-003 ; Pay assembling N° 16 / 12mm Modules AI Board Master/Slave Board for X-AI 32 01 with HiMax & Hart Connectors TB-D5016-HON-001 ; Pay assembling N° 16/12 mm Modules AI Board for IOP, HLAI, CC, P/N 51304754-150 Analog Input Type TB-D5016-HON-002 ; Pay assembling N° 16/12 mm Modules AI Board for IOP, A/O, CC, P/N 51309152-175, Analog Output Type TB-D5016-HON-003 ; Плата монтажная N° 16 / 12mm Modules Board for C-300 IOP, Universal Type for AO, DI, DO TB-D5016-HON-004 ; Плата монтажная N° 16 / 12mm Modules Board for Safety Manager AI SAI-1620m Board TB-D5016-HON-005 ; Плата монтажная N° 16 / 12mm Modules Board for Safety Manager DI SDI-1624 and SDI1608 Boards TB-D5016-HON-006 ; Плата монтажная N° 16 / 12mm Modules Board for C-300 IOP, Universal Type for AI TB-D5016-INV-002 ; Pay assembling N° 16 / 12mm Modules DI Board for FBM 217 Card, TB-D5016-INV-003 ; Pay assembling N° 16 / 12mm Modules DO Board for FBM 242 Card, TB-D5016-INV-004 ; Плата монтажная N° 16 / 12mm Modules AI/DI Board for FBM 211, 207b/c Cards, With Hart Connector TB-D5016-INV-005 ; Плата монтажная N° 32 / 12mm Modules DI Board for FBM 217 Card, Single Channel Onl TB-D5016-TRI-001 ; N° 16 / 12mm Modules AI Board for TMR 3704E/3720 Card, Dual Channel Module Only, Hart Conn.Note: N° 2 TB-D5016-TRI-001 Required each 64 Channels TMR 3704E or 3720 card, Dual Ch. Modules Only TB-D5016-TRI-002 ; N° 16+16 /12mm Mod. AI Boards for TMR 3704E/3720 Card, Single Channel Mod. Only, Hart Conn.Note: N° 2 TB-D5016-TRI-002 Required each 64 Channels TMR 3704E or 3720 card, Single Ch. Modules Only TB-D5016-TRI-003 ; N° 16 / 12mm Modules AI Board for TMR 3700/3700A/3701/3721 Cards, With Hart Connector,Note: N° 2 TB-D5016-TRI-003 Required each 32 Channels TMR 3700/3700A/3701/3721 card with Single Ch. Mod. TB-D5016-TRI-005 ; Плата монтажная N° 16+16 / 12mm Modules DI Board for TMR 3504E/3564 Card, Single Channel Only TB-D5016-TRI-006 ; N° 16 / 12mm Modules DI Board for TMR 3503E/3505E Card,Note: N° 2 TB-D5016-TRI-006 Required each 32 Channels TMR 3504E/3564 card with Single Channel Modules TB-D5016-TRI-007 ; N° 16 / 12mm Modules DI Board for TMR 3625/3664/3604E/3624 Card,Note: N° 2 TB-D5016-TRI-007 Required each 32 Channels TMR 3625/3664 card. TB-D5016-YOK-001 ; Pay assembling N° 16 / 12mm Modules AI Board for AAI 141 & AAI 143 Card, With Hart Connector TB-D5016-YOK-002 ; Pay assembling N° 16 / 12mm Modules AO Board for AAI 543 Card, With Hart Connector TB-D5016-YOK-003 ; Pay assembling N° 16 / 12mm Modules DI Board for ADV 151 Car TB-D5016-YOK-004 ; Pay assembling N° 16 / 12mm Modules DI Board for ADV 151 Card, Extention Board TB-D5016-YOK-005 ; Pay assembling N° 16 / 12mm Modules DO Board for ADV 551 Card, TB-D5016-YOK-006 ; Pay assembling N° 16 / 12mm Modules AI Board for SAI 143 Card, TB-D5016-YOK-007 ; Pay assembling N° 16 / 12mm Modules DI Board for SDV 144 Card, TB-D5016-YOK-008 ; Pay assembling N° 16 / 12mm Modules DO Board for ADV 541 Card, TB-D5024-GEB-001 ; Pay assembling N° 24 / 12mm Modules Universal 48 Channels Board with Card SUB-D and Hart Connectors TB-D5208-GMI-001 ; Pay assembling N° 8/22 mm Modules AI-AO-DI-DO Board with ELCO 56 Pin Output + Hart Connectors TB-D5216-GMI-001 ; Pay assembling N° 16/22 mm Modules AI-AO-DI-DO Board with ELCO 56 Pin Output + Hart Connectors TB-D5216-HIM-001 ; Pay assembling N° 16/12 mm Modules AI-AO-DI-DO Board 16 Channels Master Board with HiMax and Hart Connector TB-D5822-SEID-001 ; Pay assembling N° 8/12 mm Modules Board for 16 Channels with Connector Phoenix 14 Pin TB-OPT-UNI-001 ; Complete set assembling Universal Mounting Kit for for termination board D5000 Series, (1 Set), Contains:N° 1 Kit for Wall Mounting Self Tapping, N° 1 Kit for Wall Mounting M4, N° 1 Kit for TS35mm Din Rail, USB ADAPTER ; Adapter USB to serial line RS-232 Adapter to be used with PPC1092 when the PC is equipped with USB port instead of RS-232